Rotation
The logic behind this rotation is to maximize your Photon Forge and
激光利刃 uptime. You build heat in Photon Forge with
电晕爆炸,
光子闪击, and autoattack chains. Using
电晕爆炸 as your last skill and exiting Photon Forge will continue to generate heat for a few seconds without causing you to overheat. Then fill the time cooling down with Sword auto-attacks and your high damage skills such as
破片手雷 and
折射切割刀. Rinse and repeat when you fall below 100 heat.
Opener
Holosmith can vary the length of its opener by starting at different heats. This enables them to maximise damage by ending a phase just after their Photon Forge burst. Choosing the correct opener for the fight is a matter of experience, but 100% heat is a good standard:
100% Heat opener
Try to start with
布设雷区 and
投掷地雷 pre-placed (if using)
手雷包 ⇒
破片手雷
-
启用光子熔炉
-
电晕爆炸
-
光子墙
手雷弹幕 - triggers
烟花古物
引爆地雷,
引爆雷区,
粒子加速器 and/or
剑刃爆发 (whichever you have)
投掷地雷 (if using) directly onto the boss (see Notes below for details on how to use this during the rest of the rotation)
-
发射光子墙
-
激光碟片
-
光子闪击
-
巅峰射线
-
电晕爆炸
-
停止光子熔炉
Sword loop
火焰喷射 has a cooldown slightly longer than the rotation, so you alternate between using it at the start and end of your sword loop, and in the middle.
火焰喷射 - skip if it's not off cooldown
-
折射切割刀
-
破片手雷
-
毒气手雷
-
冰冻手雷
火焰喷射 - skip if it's not off cooldown
-
粘胶射击
-
闪耀弧光
阳光之刃 ⇒
阳光开膛手 ⇒
闪光马刀
-
折射切割刀
-
破片手雷
- ⇒ ⇒ x2
-
- - skip if it's not off cooldown
- - skip if you used Blowtorch
-
Photon Forge loop
-
- (if using) - this helps maintain the buff from
-
- (if using)
- - this will drift backwards in the loop over time, so use whenever it is available
- - this will drift backwards in the loop over time, so use whenever it is available
- - this will drift backwards in the loop over time, so use whenever it is available
- → → x2 - ideally you want to be above 140 heat when you use Corona Burst so depending on your speed you may need to use more or fewer autoattacks
- and (if using)
-
-
- Return to start of Sword loop
- Use off cooldown (if using). To avoid it detonating instantly, you will need to throw the mine to the edge of the target's hitbox. If you struggle with this, just replace with in the loop.
- Use , ⇒ ⇒ , and off cooldown.
- Use off cooldown, but only while in Photon Forge so that you benefit from .
Bloodstone Rotation
If using , the rotation is very similar but a bit more structured. You need to combo four blasts in quick succession, so and are essential, and this variant may struggle on bosses with high movement or disruptive mechanics.
Opener
On appropriate encounters you can start casting bomb skills before the boss spawns, but bear in mind you cannot gain stacks for outside of combat so the timing needs to be precise.
100% Heat opener
Try to start with and pre-placed (if using)
-
-
-
-
-
-
-
-
- and as soon as the buff appears
- directly onto the boss
-
-
- ⇒ ⇒ - you don't have to complete the chain if you're in danger of overheating
-
-
Sword loop
-
-
-
-
- if available, otherwise ⇒
- ⇒ ⇒
-
- ⇒ ⇒ x2
-
-
-
-
-
-
-
Photon Forge loop
-
-
-
-
- and as soon as the buff appears
-
- → → x2 - ideally you want to be above 140 heat when you use Corona Burst so depending on your speed you may need to use more or fewer autoattacks
-
-
- Return to start of Sword loop
Notes
- Under no circumstances should you ever overheat as it will massively reduce your damage output. Try to exit photon forge as close to 149 heat as possible.
- will continue to generate heat for a short time after it finishes, but it will not trigger an overheat if you are not in forge. For this reason, it should be the last skill you use while in Photon Forge.
- If you are a little slow with the rotation outside of Photon Forge, you may find that you are not close to 149 heat when you would normally exit. In this case, perform extra Photon Forge autos.